| title: | Re Hauppauge HVR 1700 Support |
|
Torben Viets wrote:
Hello,
thanks for the quick reply.
Steven Toth wrote:
Torben Viets wrote:
Hello,
I have a Hauppauge HVR-1700 PCI Express, I have read all posts about
this card here, but I didnt get it working, how does it work?
Its working fine for me on a stock 7.10 ubuntu install.
Kernel: linux-2.6.25-git10
Firmware-Files:
ls -al /lib/firmware/2.6.25-git10/
total 416
drwxr-xr-x 2 root root 91 Apr 27 16:27 .
drwxr-xr-x 3 root root 25 Apr 27 16:26 ..
-rw-r--r-- 1 root root 24878 Apr 27 16:27 dvb-fe-tda10048-1.0.fw
-r--r--r-- 1 root root 16382 Apr 27 16:27 v4l-cx23885-avcore-01.fw
-r--r--r-- 1 root root 376836 Apr 27 16:26 v4l-cx23885-enc.fw
The modules I use are from the actual v4l-dvb hg, if I type make load,
the only thing I get is a /dev/video0, but I have no picture with
xawtv...
/dev/video doesnt work, its not supported.
Are there any plans to support it?
No immediate plans.
You should aim to use the dvb-apps tools (tzap, scan) and mplayer as
example tools, or MythTV as an app.
The DVB doesnt work at all, I have no /dev/dvb*, here is my dmesg:
cx23885 driver version 0.0.1 loaded
ACPI: PCI Interrupt 0000:02:00.0[A] - GSI 24 (level, low) - IRQ 24
CORE cx23885[0]: subsystem: 0070:8101, board: Hauppauge WinTV-HVR1700
[card=8,autodetected]
cx23885[0]: i2c bus 0 registered
cx23885[0]: i2c bus 1 registered
cx23885[0]: i2c bus 2 registered
tveeprom 0-0050: Huh, no eeprom present (err=-5)?
tveeprom 0-0050: Encountered bad packet header [00].
Corrupt or not a Hauppauge
eeprom.
cx23885[0]: warning: unknown hauppauge model #0
cx23885[0]: hauppauge eeprom: model=0
cx23885[0]: cx23885 based dvb card
tda10048_readreg: readreg error (ret == -5)
cx23885[0]: frontend initialization failed
cx23885_dvb_register() dvb_register failed err = -1
cx23885_dev_setup() Failed to register dvb on VID_C
cx23885_dev_checkrevision() New hardware revision found 0x0
cx23885_dev_checkrevision() Hardware revision unknown 0x0
cx23885[0]/0: found at 0000:02:00.0, rev: 2, irq: 24, latency: 0, mmio:
0xfe800000
This looks bad, it looks like i2c is broken badly, so that the eeprom
isnt detected and the demodulator isnt found during attach. This is
the reason why your missing /dev/dvb/adapterX/
No idea why. Try loading the cx23885 with debug=5 and report any log
messages here - on this mailing list.
here ist the debug=5 output
cx23885[0]/0: cx23885_dev_setup() Memory configured for PCIe bridge type
885
cx23885[0]/0: cx23885_init_tsport(portno=2)
CORE cx23885[0]: subsystem: 0070:8101, board: Hauppauge WinTV-HVR1700
[card=8,autodetected]
cx23885[0]/0: cx23885_pci_quirks()
cx23885[0]/0: cx23885_dev_setup() tuner_type = 0x0 tuner_addr = 0x0
cx23885[0]/0: cx23885_dev_setup() radio_type = 0x0 radio_addr = 0x0
cx23885[0]/0: cx23885_reset()
cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [VID A]
cx23885[0]/0: cx23885_sram_channel_setup() 0x000107b0 <- 0x00000040
cx23885[0]/0: cx23885_sram_channel_setup() 0x000107c0 <- 0x00000b80
cx23885[0]/0: cx23885_sram_channel_setup() 0x000107d0 <- 0x000016c0
cx23885[0]/0: [bridge 885] sram setup VID A: bpl=2880 lines=3
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch2]
cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS1 B]
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010400 <- 0x00005000
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010410 <- 0x000052f0
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010420 <- 0x000055e0
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010430 <- 0x000058d0
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010440 <- 0x00005bc0
cx23885[0]/0: [bridge 885] sram setup TS1 B: bpl=752 lines=5
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch4]
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch5]
cx23885[0]/0: cx23885_sram_channel_setup() Configuring channel [TS2 C]
cx23885[0]/0: cx23885_sram_channel_setup() 0x000108d0 <- 0x00006000
cx23885[0]/0: cx23885_sram_channel_setup() 0x000108e0 <- 0x000062f0
cx23885[0]/0: cx23885_sram_channel_setup() 0x000108f0 <- 0x000065e0
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010900 <- 0x000068d0
cx23885[0]/0: cx23885_sram_channel_setup() 0x00010910 <- 0x00006bc0
cx23885[0]/0: [bridge 885] sram setup TS2 C: bpl=752 lines=5
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch7]
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch8]
cx23885[0]/0: cx23885_sram_channel_setup() Erasing channel [ch9]
cx23885[0]: i2c bus 0 registered
cx23885[0]: i2c bus 1 registered
cx23885[0]: i2c bus 2 registered
Everything looks fine up to this point, then i2c looks bad.
Can you try again with modprobe cx23885 i2c_scan=1 and post the output
again? (Output will be large - feel free to use pastebin.com and post
the URL here).
Regards,
Steve
_______________________________________________
linux-dvb mailing list
linux-dvb@xxxxxxxxxxx
rel="nofollow" www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb
|
